ss400 steel conversion thickness

Comparison of ASTM A36 steel plate and SS400 steel plate

Steel grades ASTM A36 and SS400 under JIS G3101 both are common used carbon structure steels,mild steels.When rolling steel plates ASTM Grade A36,As rolled or Controlled rolled is ok for thickness belows 40mm (1.5inch) normally.If above 40mm (1.5inch),customers can choose Normalized for improve steel property.Stee plates SS400 is also the same.

GAUGE TO THICKNESS CHART - Stainless Supply

GAUGE TO THICKNESS CHART (Click here for a printable PDF chart) Gauge. Stainless. Galvanized. Sheet Steel JIS G3101 General Structure Hot Rolled SS400 Steel ASTM The yield strength for thickness below 16 mm is minimum 245 N/mm2 (MPa) whereas for higher gauges above 100 mm is minimum 205 N/mm2 (MPa). The elongation property of SS400 steel varies with the ranges of thickness. The minimum percentage ranges for elongation is 17% thicknesses till 16 mm, 21% for thicknesses till 40 mm, and 23% greater than 50 mm.

JIS G3101 SS400 Structural Carbon Steel Plate Specification

Thickness 16 mm:Thickness 16mm:Thickness 5mm:Thickness 5-16mm:Thickness 16mm:SS400:245:235:400-510:21:17:21- Japan (JIS ) - Steel Worldwide equivalent gradesss400 ss490 ss490b ss490c ss490ya ss500 stba12 stkm12a suh309 suh330 suh35 suj2 sup10 sus201 sus301 sus301l sus303 sus304 sus304h sus304l sus304ln sus305j1 jis steel equivalents afnor, nbn, une, gb, ss, bds, msz, pn, sfs, onorm, as, is, nen, ds.

Mild Steel Plate Dimensions Weight Sizes Thickness Chart

Check Mild Steel Plate Material Grades S355 / 250 / 43a / Checker Plate Dimensions Weight Sizes Thickness Chart / Properties / Chemical Composition / Density. We are highly engaged in offering our clients a high quality range of MS Plate (Mild Steel Plate). - Global Stainless is a finest and appreciable Supplier and exporter of Mild Steel Q235 Steel Plate Equivalent Steel Standard-ASTM A36Substitution of A36, SS400 and Q235 steel plate. Although the Q235 steel grade steel plate has lower mechanical properties than A36 and SS400 material, but in actual operation process, as long as the buyers do not have special requirement, often these three kinds of materials can be substituted.

Rangkuman DiskusiBeda ASTM A36 dan JIS 3101 SS 400

Translate this pageFeb 02, 2011 · Difference is that Ss 400 has no chemical composition assigned, while A36 is allowed for max. 0.25% C and 0.40% Si. In case when thickness is over 3/4 to 1 1/2 [20 to 40], incl., max. 0.80-1.20% Mn is also assigned for A36. Japanese standard JIS G 3101 recognizes 4 grades of steel:Ss 330, Ss 400, Ss 490 and Ss 540. SPCC Steel Quality Aspects Explained For ConsumersNov 25, 2012 · Conformance of Chemistry:This is one of the main quality aspect of SPCC steel, since this aspect influences others aspects of the product.For example the chemical composition defines many of the mechanical properties of the product. JIS G 3141 defines the tolerance limits of the chemical composition.. There are two ways for chemical verification of the SPCC steel, which customer is

STEEL GUIDE - Metal by the Metre

Aluminium Hollows & Round Tubes 41 Conversion Tables 100 Aluminium Machine Round, Stainless Steel Sheets 42 Birmingham Gauge Converter - Aust Standards 101 Stainless Steel Flats - Squares 43 Common Metal terms - Page1 102 Stainless Steel Angles - Rounds 44 Common Metal terms - Page 2 103 Stainless Steel Pipes - Polished Pipes 45 Notes 104 SUBSTITUTE MATERIAL (JIS, BS, DIN ) FOR ASTM Structural Steel G 3101 SS400 4360 Gr 40A (1) 17100 St44-2 G 3105 SM400A 4360 Gr 438 (1) 17100 St44-3 A-131 Note (2):Plates over 1-3/8 Inches (35 m-n) in thickness shall be normalized. Note (3):For cold rolled sheet and strip, use corresponding SUS-CP and SUS-CS steels, according to JIS G 4305 and G 4307, respectively.

Sheet Metal Gauge Chart Metal Supermarkets - Steel

Feb 01, 2018 · A gauge conversion chart can be used to determine the actual thickness of sheet metal in inches or millimeters. For example, 18 gauge steel, according to a gauge conversion chart, is 0.0478 inch or 1.214 millimeter. The gauge number 18 holds no relevance to the actual measurements. Sheet Metal Gauge Thickness Chart (to mm/inch Conversions 37 rows · Ga. is different from inches, there is no conversion formula. Even when the non-ferrous

Stainless Steel Pipes Dimension (Schedule, Wall Tickness

Stainless Steel Pipes Dimension (Schedule, Wall Tickness & Weight) OD (mm) - W.T. (mm) XW.T. (mm) X 0.02466 = Kg. per mtr. Stainless Steel:Tables of Technical PropertiesCare was taken to include as much information as possible about stainless steel flat products used throughout Europe, for the informatio n of the user: Chemical and physical properties are in accordance with EN 10088-1:2005 Mechanical properties are in accordanc e with EN 10088-2:2005, except for he

Steel Plates - Size & Weight - Engineering ToolBox

  • Steel Plate Thickness and Weight - Imperial UnitsCalculating Steel Plate WeightSteel Plate Thickness and Weight - Metric UnitsHandbook of Comparative Handbook World Steel Comparing steel standards is not an exact science, so the biggest challenge of preparing such a book was deciding on the "rules of comparison." Of the similar books on the market today, none explain in detail why one steel is comparable to another. They simply appear together in a list of steels. I kept a U006en Special Steel Sheets and CoilsSTEEL CORPORATION with respect to the use of the information contained herein. The information in this publication is subject to change or modification without notice. Please contact the NIPPON STEEL CORPORATION office for the latest information. Please refrain from unauthorized reproduction or copying of the contents . of this publication.

    Weight Table of Stainless Steel Plate

    offers including:Finish Type, Stainless steel material, Stainless steel Sheet, Stainless steel coil, Stainless steel strip XLER Entire Brochure - BlueScope SteelBlueScope Steel distributors around Australia and New Zealand and is available on very short lead times. THICKNESS WIDTH LENGTH (AS 1548-7-430R) 5 2400 9.0 (AS 1548-7-460R) 6 3100 9.6 8 3100 9.6 10 3100 9.6 12 3100 9.6 16 3100 9.6 20 3100 9.6 25 3100 9.6 32 3100 9.6 40 2400 9.6

    SS400 (JIS ) - Worldwide equivalent grades - Steel Number

    S275JR (1.0044) , S235JR (1.0038 (dubl)) , SS400 (Japan, JIS ) - European (EU, EN) and wordwide Steel equivalent grades. These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt.